#adOTC#ad - Quickly and easily removes sealed U-joint cups without the need for hammering or heat. May be used with up to a one-inch impact wrench. Fits practically all Class 7 and 8 trucks. Will not damage the driveshaft yoke bearing cups or joints. Ideal tool for disassembling drivelines.
OTC#ad - Six adapters increase application coverage; includes tie rod/ball joint tool and two Ford axle installers. 3/4 inch custom drive screw coupled with the special equalizer washer ensures smooth operation while proprietary heat treating provides 5 to 10 times longer life than similar designs.
Included application Guide is the most comprehensive on the market.
Jaws are designed and sized to properly fit hub applications and can be quickly located on the puller bar without the need for fasteners. The hub grappler is a complete solution for servicing wheel hubs/bearings on the vehicle w/o removing the steering components or knuckle - eliminating unnecessary alignments or the use of a shop press.
This reduces damage and increases the amount of applications. All three pullers have been redesigned to make the removal of semi-floating rear axle bearings easier. Includes one each 7495a 7496A and 7497A and a storage case.
#adOTC#ad - Set components deliver a spread of 3 inches to 5 inches and a reach of 1 inch to 2-1/4 inches. Kit includes 2 ea. For a wide range of pulling jobs including: bearings; alternator, power steering, generator, and crankshaft pulleys; timing gears; harmonic balancers; and more.
Clamp bolts, 1 pair of jaw pins with ball spring, 2 ea.
Durable blow-molded plastic storage case that keeps set components contained and organized so they are ready for use when needed. Cross-bar yokes, and 3 pairs of capped bolts. Drop-forged components can be used in a variety of combinations. Forcing screws live center, 3 pairs of puller jaws, 2 ea.
#adOTC#ad - Jaws can be set up for 2 or 3-way internal or external pulling for the ultimate in tool flexibility. 05378 - grip wrench adapter w/single lead wrench not included; 205377 - Dent Puller, 309321 - Forcing Screw; 215895 - Sleeve; durable blow-molded case keeps set components contained and organized.
Includes: 1155 slide hammer with 5 lb. 34698 - 3ea. Otc's 7948 'silver slapper' 10-way slide hammer puller Set with Storage Case allows you to pull flange-type rear axles, remove stubborn oil seals and bearings and other press-fit parts.
Designed to make quick work of pulling stubborn, rusted pilot bearings. Puller's forcing screw expands the jaws inside the bearing and simultaneously pushes against the bottom of the blind hole to quickly remove the bearing/bushing.
#adOTC#ad - High-grade materials ensure quality performance over the lifetime of the tool; comprehensive instructions included. Next, bridge is removed and slide hammer assembly is attached - with a few sharp hammer blows from the 5 lb.
This tool removes cylinder sleeves faster than ordinary pullers because it requires little setup time - cone adjustment positions puller jaws quickly then locking bar is tightened - ready to go.
To break 'frozen' sleeves loose, adjustable bridge is positioned on the cylinder block then bearing-mounted forcing nut is tightened. Hammer, sleeve is pulled - an average of less than 2 minutes per cylinder in most cases. Does not require any special adapters to pull sleeves due to adjustable jaw design; adjustable jaws allow use on cylinder sleeves ranging from 3 inches to as large as 6-1/2 inches in diameter.
#adOTC#ad - 3/8-16 x 3 inch cap screws - spread range: 1-1/2 to 4-1/4 inches; 1122 - Bearing Pulling Attachment for 1027/7393 pullers with 1/8 to 2 inch spread range. 1177 slide hammer for rear axle flanges.
Reach and 4-3/4 inches max. Otc's 1181 multi-purpose puller set includes a broad assortment of puller tools that provide a wide range of job versatility. 7208a - front hub puller for servicing front-wheel-drive cars; includes a spare locknut permitting use with the No.
#adOTC#ad - Removes front and rear countershaft bearings from the main case of Eaton/Fuller 2 Series Roadranger transmissions. Set includes pulling collet, sleeve, and a pair of puller legs; note: this is not a stand-alone tool - must be used with OTC's 7070A.